
Water Heater Leaking? What to Do Right Now in Lehi
Water spreading from a water heater in your Lehi home? Close the cold-water valve, kill the power or gas, then call or text and you'll get a call right back.
Updated Prices checked
- Answered 24/7, nights and weekends
- Garage, closet and basement leaks
- Price before any work starts
Water heater trouble?
Leaking right now? Three things before anything else
- Shut off the water. Turn the cold-water supply valve on the pipe at the top of the heater clockwise until it stops.
- Cut the power. Electric unit: switch off its breaker at the panel. Gas unit: turn the gas control knob on the front of the heater to OFF.
- Then call or text (385) 336-3299. Answered 24/7, and you'll get a call right back.
Smell gas? Leave the house, don't flip any switches, and call 911 and then Enbridge Gas Utah's leak line at 800-767-1689 from outside.
Pooling water is stressful, all the more if you find it on a winter morning or come home to it after a trip. The steps below keep the damage small until a licensed plumber can look at the heater.
What comes first when the tank is dripping?
Follow the three shutoff steps in the red box above, then slow down and look. Most of the damage from a leak comes from the water that keeps arriving after you first notice it, so the cold-water valve matters more than anything else.
- Quarter-turn handle: turning it until it sits crosswise to the pipe closes it.
- Round wheel handle: turn it clockwise until it stops, and don't force it past that.
- Stuck valve: close the main shutoff for the house instead, usually where the water line enters near the street side of the home.
Once the supply is off, put towels or a wet-vac to work and keep children and pets away from the area, especially if the water is hot.
Where is the water actually coming from?
A leak starts in one of five places, and where it starts tells you whether the heater can live. Dry the jacket and the fittings with a towel, wait a few minutes, and watch where the first bead of fresh water appears.
- Top connections: the hot and cold fittings and flex connectors weep at their threads, and water runs down the side of the tank.
- Relief valve and discharge pipe: a drip here means the tank is venting pressure or heat.
- Drain valve: a slow drip from the little valve near the bottom is common on older tanks and often a simple swap.
- Heating element gaskets: on electric heaters, water seeping from behind a side access panel points to a failed gasket.
- The tank body: water welling from the bottom or through the jacket means the steel has corroded through.

A rusty stain or a wet insulation layer behind the panels tells the same story. If you can dry everything and the tank stays dry, a fitting is the likelier culprit.
Why does the relief valve keep dripping in Lehi?
A relief valve drips when pressure inside the tank is too high, and some parts of Lehi sit at high water pressure. The city's own planning model for the Cold Spring Ranch area, for example, models static pressures from about 70 to 107 psi. Those are modeled figures, not readings from your pipes, but they explain why pressure-reducing valves are common in parts of town.
A heater on a closed plumbing system, one with a pressure-reducing valve, check valve or backflow preventer at the house entry, also needs an expansion tank. Without one, the extra volume the water takes up when it heats has nowhere to go, and the relief valve opens instead. A drip every time the heater cycles often means a waterlogged expansion tank or a missing one, not a bad valve.
Dripping valve or pooled water? Call or text and get a price before any work.
Does the Utah code have anything to say about leaks?
Yes, two parts of it matter here. Utah's construction code requires a water heater to be anchored or strapped against earthquake motion, with straps in the upper and lower thirds of the tank (Utah Code 15A-3-205). A tank that has shifted off its straps can strain its own pipe connections, and loose fittings are one more way a leak begins.
The same section covers drain pans. A heater sitting where a leak could damage the building generally needs a pan, and the pan's drain line serves that heater alone, with its own trap and vent. If your heater has no pan and sits above a finished ceiling, ask about adding one when it is replaced.
Can I just keep using a heater that leaks a little?
No. A leaking tank is not a stable situation, because the metal around a pinhole keeps corroding and every heating cycle pushes more water through it. Stopping use now costs a cold shower, while waiting can cost a floor, a ceiling or a finished basement.
- Fitting or valve leaks: the heater can usually go back into service after a repair.
- Tank leaks: nothing patches a steel tank from the outside, so plan on a replacement.
- Slow weep you can't locate: treat it like a tank leak until proven otherwise, since hidden seepage damages framing quietly.
Could freezing weather cause a leak?
It can. Freezing winter nights are routine in Lehi, and a heater in an unheated garage, an exterior closet or a crawl space shares that cold. Uninsulated pipes and the relief discharge line are the usual weak points, and a split from a freeze often stays hidden until the thaw.
After a hard freeze, walk past the heater and the pipes around it before you run the water. A new drip or a patch of ice-damp insulation is worth a call. Wrapping exposed lines is cheap, and it is part of what to ask about when a heater in a garage is replaced.
What does a leak repair cost?
Nationally, a repair visit averages about $200 to $850 and a relief valve $35 to $250. One national repair company reports Utah replacement running around 10% above its national average. Read every online price as a starting point; the real figure for your heater comes before work is booked.
| Leak source | National range | Notes |
|---|---|---|
| temperature and pressure (T&P) relief valve | $35–$250 | valve only, plus discharge pipe if needed |
| Anode rod | $100–$250 | worn rods speed up tank corrosion |
| Expansion tank, installed | $225–$625 | for closed plumbing systems |
| Tank replaced | $1,000–$3,400 | when the tank wall has failed |
Every dollar range in this guide is a rounded national average, with the working shown on the pricing page.
What if the leak is the gas line, not water?
Different rules apply. A gas smell near the heater means leave the house, leave the lights and switches alone, and call 911 plus Enbridge Gas Utah's leak line at 800-767-1689 from somewhere safe. Enbridge takes leak reports by phone only, and homeowners should never try to turn gas valves on or off at the meter.
Water stains below a gas heater are a separate matter, and both can be true at once. When you smell gas, handle that first, then deal with the water.
When is it time to replace instead of repair?
Replace when the tank wall is leaking, or when the heater is past a decade old and the repair would be the second or third part in a row. A typical tank lasts 8 to 12 years, sometimes longer, so age matters. Read the date on the data plate, which is sometimes coded into the serial number.
Our water heater replacement page covers what a swap involves in Lehi, including the permit and the earthquake strapping. Get a price and you'll hear the repair-versus-replace math on your own heater, not a national average.
- Cold-water valve closed
- Power off at the breaker, or gas control set to off
- Water dried so the source is visible
- Photos taken of the leak and any damage
- Call placed before the pan overflows
Stop the leak and get your price: call or text any hour.
Questions homeowners ask
Should I turn off a leaking water heater right away?
Yes. Close the cold-water valve on the pipe above the tank, then switch off the breaker or turn the gas control to its off setting. A tank that keeps heating while it leaks wastes water and can damage the floor under it.
Why is water dripping from the pipe next to my water heater?
That pipe is the discharge line from the temperature and pressure relief valve, and it only drips when pressure or heat inside the tank climbs too high. A few drips can point to high water pressure or a worn valve, while a steady stream needs attention today.
Can a leaking water heater be repaired?
It depends on where the water comes from. Leaks at a fitting, valve, flex connector or drain valve are usually repairable, while a leak through the tank wall means the heater has to be replaced.
Is a leaking gas water heater dangerous?
Water by itself is a flooding problem, but a gas smell is a different emergency. If you smell gas, get everyone outside, then call 911 and Enbridge Gas Utah at 800-767-1689 from a safe place.
What does it cost to fix a leaking water heater in Lehi?
National averages put a repair visit at about $200 to $850 and a relief valve alone at $35 to $250. A tank that has rusted through means replacement, nationally about $1,000 to $3,400 installed.
Last updated: